Radar current meter / Radio wave current meter
Radar current meter / Radio wave current meter
Radar current meter / Radio wave current meter
Radar current meter / Radio wave current meter
Radar current meter / Radio wave current meter
Radar current meter / Radio wave current meter
Radar current meter / Radio wave current meter
Radar current meter / Radio wave current meter
Radar current meter / Radio wave current meter
Radar current meter / Radio wave current meter
Radar current meter / Radio wave current meter
Radar current meter / Radio wave current meter
Radar current meter / Radio wave current meter
Radar current meter / Radio wave current meter
Radar current meter / Radio wave current meter
Radar current meter / Radio wave current meter

Radar current meter / Radio wave current meter

$520.00
Color:silvery white
Weight:1.5kg
measure distance:NO
voltage:12V
Quantity
Click to Buy
Click to consult
Detail

Operating Parameters

Parameter

Description

Supply Voltage

DC 7~28V

Current (12V Power Supply)

Average current is about 60mA (5—100mA) during normal operation

Operating Temperature

-40~85°C

Waterproof Rating

IP68

Transmission Frequency

Adjustable 25.75~26GHz

Communication Interface

RS-485

Communication Protocol

MODBUS-RTU

2. Measurement Parameters

Parameter

Description

Current Measurement Range

0~15m/s

Current Measurement Accuracy

±0.02m/s

Resolution

0.01m/s

Effective Distance

0.2~30m

Start-up Time

<3s

Measurement Direction

Bidirectional

Automatic Angle Correction

30°~60°

3. Wiring Instructions

Four-core Cable Definition:

Pin No.

Color

Definition

1

Red

Power Positive (+)

2

Blue

Power Ground (-)

3

Brown

RS485_A(+)

4

Yellow

RS485_B(-)

Installation Angle Requirement: The installation angle of the current meter should be 45~60 degrees, which refers to the angle between the antenna beam direction of the current meter and the horizontal plane. For river channels with uneven water flow, small angles are prone to data jump. A larger installation angle can better suppress rainfall interference and improve signal quality; it is recommended to set the installation angle to about 60 degrees. After installation, the angle can be read through communication to ensure the accuracy of measured data.

4. Communication Interface

4.1 RS485 Interface

Basic communication settings for RS485 interface are as follows:

Parameter

Setting

Baud Rate

9600 (default, configurable)

Parity Bit

None

Data Bits

8

Stop Bits

1

5. MODBUS Protocol

5.1 RTU Frame Structure

In RTU mode, a new message must start with a silent period of at least 3.5 character times, followed by the first field: the address field. The entire message frame must be transmitted as a continuous data stream. If there is an interval exceeding 1.5 character times before the end of the message, a communication error will occur.

Start

Device Address

Function Code

Data

CRC Check

End

T1-T2-T3-T4

8Bit

8Bit

n 8Bits

16 Bit

T1-T2-T3-T4

Field Explanation:

• Address Field: The valid address range of the slave (target device) is 1~247, supporting broadcast send-receive address 0xFF and broadcast receive-only address 0xFE. When using the broadcast address, ensure that only one sensor is connected; otherwise, data errors or hardware damage may occur.

• Function Field: Valid function code range is 1~255. The radar current meter supports function codes 0x03, 0x06, and 0x10.

• Data Field: Composed of multiple groups of hexadecimal data, with two hexadecimal digits as one group, ranging from 00~FF.

• CRC Check Code: After CRC calculation, the low byte is transmitted first, and the high byte is transmitted later.

• T1-T2-T3-T4: Represent the transmission time of each byte, totaling four byte transmission delay times.

Supplementary Communication Specifications:

• Baud Rate/Parity/Data Bits/Stop Bits: 9600/None/8/1 (The upper computer serial port number ranges from 1 to 20, facilitating communication with USB-to-serial cables extended by USB-HUB).

• RS485 Communication: Half-duplex communication, supporting one master and multiple slaves; two-wire system, differential signal, twisted pair recommended.

• Data Rule: The high bit of the data area is transmitted first.

• CRC Check Rule: When the CRC result is placed in the message frame, the low byte comes first.

5.2 Radar Current Meter Register Table

Note: U16 = Unsigned 16-bit integer

No.

Register Address

Function Description

Unit

Remarks

1

00H

Device Temperature (signed number, scale factor ×100)

0.01°C

Invalid

2

01H

Instantaneous Current Velocity

mm/s

For testing

3

02H

Average Current Velocity

mm/s

Recommended for customer use

4

03H

Reserved

-

-

5

04H

Flow Direction

-

1: Downstream; 2: Upstream

6

05H

Installation Angle (scale factor ×100)

0.01°

Angle with horizontal plane

7

06H

Device Voltage

mV

Device power supply voltage

8

07H

Jump Filter Status

-

1: Jump; 0: Normal

9

08H

Instantaneous Flow Rate

m³/S

Independent flow register, discontinuous from previous registers

10

09H

Water Depth

cm

-

11

0AH

Midline Current Velocity

mm/s

-

12

0BH

Low Power Consumption Setting

-

0x001: Low power consumption; 0x002: Non-low power consumption

13

0CH

Baud Rate Setting

-

0x001: 9600; 0x002: 115200

14

0DH

Gain Value

-

0x0000: Auto gain; Other values: Manual gain

15

0EH

Time Domain Threshold

-

-

16

0FH

Frequency Domain Threshold

-

-

17

A0H

Device Address

-

-