Ultrasonic Level Meter
Ultrasonic Level Meter
Ultrasonic Level Meter
Ultrasonic Level Meter
Ultrasonic Level Meter
Ultrasonic Level Meter
Ultrasonic Level Meter
Ultrasonic Level Meter
Ultrasonic Level Meter
Ultrasonic Level Meter
Ultrasonic Level Meter
Ultrasonic Level Meter

Ultrasonic Level Meter

$200.00
Color:black
Weight:0.5kg
measure distance:0~7m
voltage:12V
Quantity
Click to Buy
Click to consult
Detail

Technical Parameters

Parameter

Description

Supply Voltage

DC 7~28V

Current (12V Power Supply)

30mA

Operating Temperature

-20~60°C

Waterproof Rating

IP65

Transmission Type

Ultrasonic

Communication Interface

RS-485

Communication Protocol

MODBUS-RTU

Distance Measurement Range

7m

Measurement Accuracy

±3mm

Resolution

1mm

Measurement Time

1s

Start-up Time

<3s

2. Connector Definition

Four-core Cable Definition:

Pin No.

Color

Definition

1

Red

Power Positive

2

Blue

Power Ground

3

Brown

RS485_A(+)

4

Yellow

RS485_B(-)

3. Installation Instructions

When installing the level meter, the beam of the level meter must be perpendicular to the measured surface. The surface to be measured should be as flat as possible. The radiation angle of the level meter is 12 degrees, and it measures a plane rather than a point. The readback data is the distance of the surface with the largest reflection area. If there are steps on the test surface, it is likely to cause errors in the measured data.

Refer to the cable description according to the actual goods.

4. 485 Communication Protocol

4.1 Basic Communication Settings

Parameter

Setting

Baud Rate

9600/115200 (default: 9600)

Parity Bit

None

Data Bits

8

Stop Bits

1

4.2 Communication Specifications

RS485: Half-duplex communication, supporting one master and multiple slaves; two-wire system, differential signal, twisted pair is recommended.

Data Rule: The high bit of the data area is transmitted first.

CRC Check Rule: When the CRC result is placed in the message frame, the low byte comes first.

Supplementary Notes: The upper computer serial port number ranges from 1 to 20, facilitating communication with USB-to-serial cables extended by USB-HUB.

4.3 Protocol Example

Send: 01 (Address) 03 (Function Code) 00 01 (Starting Register Address: 01) 00 01 (Read 1 Data) D5 CA (CRC Check)

Receive: 01 (Address) 03 (Function Code) 02 (Number of Bytes Read) 00 01 (Empty Height: 1mm) XX XX (CRC Check)

5. Quick Start Commands

Measurement Item

Type

Content

Empty Height

Command

01 03 00 00 00 01 84 0A


Response

01 03 02 00 01 79 84


Parameter Description

The returned result is 2 bytes, where 0x0001 is in hexadecimal, converted to decimal is 1, indicating 1 cm

Empty Height

Command

01 03 00 01 00 01 D5 CA


Response

01 03 02 00 02 39 85


Parameter Description

The returned result is 2 bytes, where 0x0002 is in hexadecimal, converted to decimal is 2, indicating 2 mm

6. MODBUS Protocol - Read-Only Registers

Note: U16 = Unsigned 16-bit integer

No.

Register Address

Function

Unit

Remarks

1

00H

Empty Height

cm


2

01H

Empty Height

mm


3

02H

Water Depth

cm

Default is 20 meters minus empty height; total height can be set

4

03H

Water Depth

mm

Default is 20 meters minus empty height; total height can be set

5

04H

Address


Default 0X01

6

05H

Reserved



7

06H

Start Distance

cm


8

07H

End Distance

cm


9

08H

Low Power Consumption Setting


0x001: Low power consumption; 0x002: Non-low power consumption

10

09H

Baud Rate


0x001: 9600; 0x002: 115200

11

0AH

Reserved


Returns 0X0

12

0BH

Calibration


0x0000: 0; When setting a negative number, it is 32768 + the absolute value of the negative number to be set; When setting a positive number, set it directly. Unit: mm

13

0CH

Reserved


Returns 0